RUNNING TOOL
‘RX’ RUNNING TOOL
‘W’ RUNNING TOOL
‘X & R’ RUNNING TOOL
MODEL ‘C-1’ RUNNING TOOL
‘RX’ RUNNING TOOL
The ACT “RX” Running Tool sets X, XN, R, RN, and RQ Locking Mandrels in the top type X, XN, R, RN and RQ landing nipples. This tool is generally used for installing safety valves in the uppermost landing nipple. With this tool, the lock mandrel may be run with the keys in the control or locating positions. The lock mandrel keys act as a no-go to locate the nipple rather than the dogs on the running tool. When a non-no-go lock is being run, the keys must be run in the locating position and the lock must be set in the first nipple in the bore of that lock. The position of a snap ring in the tool gives a positive indication when the lock is fully set.
| ‘RX’ RUNNING TOOL | ||||
|---|---|---|---|---|
| Nominal Size (in) | Max. O.D. (in) | F/N O.D. (in) | Top Connection | Part No. |
| 2.313 | 2.12 | 1.750 | 15/16 - 10 UN | RX-2313 |
| 2.750 | 2.62 | 2.313 | 1-1/16 - 10 UN | RX-275 |
| 3.125 | 3.09 | 2.313 | 1-1/16 - 10 UN | RX-312 |
| 3.313 | 3.09 | 2.313 | 1-1/16 - 10 UN | RX-313 |
| 3.688 | 3.62 | 2.313 | 1-1/16 - 10 UN | RX-368 |
| 3.813 | 3.62 | 2.313 | 1-1/16 - 10 UN | RX-381 |
| 4.562 | 4.50 | 3.125 | 1-1/16 - 10 UN | RX-456 |
| 5.875 | 5.80 | 3.125 | 1-1/16 - 10 UN | RX-587 |
| 5.963 | 5.81 | 3.125 | 1-1/16 - 10 UN | RX-596 |
‘W’ RUNNING TOOL
The ACT ‘W’ Running Tool sets type B, C and W slip type mandrels in the tubing. The W Running Tool consists of a top sub complete with a fishing neck and sucker rod pin connection, a middle sub, a bottom sub, a collet set and an inner core.
When the desired setting depth has been reached the tools are picked up to set the slips and expand the rubber element. Once set, the pin in the W Running Tool can be sheared and the prong can be withdrawn from behind the collet, allowing the running tool to release from the mandrel.
| ‘W’ RUNNING TOOL | ||||||
|---|---|---|---|---|---|---|
| Used to Run | Nominal Size (in) |
Max. O.D. (in) | F/N O.D. (in) | Will Engage Fishing Neck (in) |
Top Connection |
Part Number |
| 1-1/4 | 1.190 | 1.000 | 0.531 | 5/8 -11 UNC | 257-125 | |
| 1-1/2 -1-3/4 | 1.380 | 1.187 | 0.687 | 15/16 - 10 UN | 257-175 | |
| Type | 2 | 1.500 | 1.375 | 0.812 | 15/16 - 10 UN | 257-200 |
| B, C & W | 2-1/2 | 1.500 | 1.375 | 1.000 | 15/16 - 10 UN | 257-250 |
| Mandrels | 3 | 2.250 | 1.750 | 2.000 | 1-1/16 - 10 UN | 257-300 |
| 3-1/2 | 2.620 | 2.313 | 1.875 | 1-1/16 - 10 UN | 257-350 | |
| 4 | 3.500 | 2.313 | 2.812 | 1-1/16 - 10 UN | 257-400 | |
‘X & R’ RUNNING TOOL
The ACT X and R Running Tools are used to set model ‘X’, ‘XN’, ‘R’, ‘RN’ and ‘RQ’ Lock Mandrels in their respective landing nipples. The X and R Running Tool can be set up to run either in selective or non-selective mode. In selective mode the lock mandrel can be run through several landing nipples of the same size and type before selecting the desired nipple to set the lock mandrel. In non-selective mode, the lock mandrel will locate the first corresponding nipple.
| ‘X & R’ RUNNING TOOL | |||||
|---|---|---|---|---|---|
| Max. O.D.(in) | To Suit Nipple Bore (in) | F/N O.D. (in) | Top Connection | Part No. ‘X’ | Part No. ‘R’ |
| 1.720 | 1.875 | 1.375 | 15/16-10 UN | 174-187 | 275-187 |
| 2.171 | 2.313 | 1.750 | 15/16-10 UN | 174-231 | 275-231 |
| 2.687 | 2.750 | 2.313 | 1-1/16-10 UN | 174-275 | 275-275 |
| 2.843 | 2.875 | 2.313 | 1-1/16-10 UN | 174-288 | 275-288 |
| 3.250 | 3.313 | 2.313 | 1-1/16-10 UN | 174-331 | 275-331 |
| 3.750 | 3.813 | 2.313 | 1-1/16-10 UN | 174-381 | 275-381 |
| 4.500 | 4.562 | 3.125 | 1-1/16-10 UN | 174-456 | 275-456 |
MODEL ‘C-1’ RUNNING TOOL
The ACT ‘C-1’ Running Tool is used to run ACT flow control devices that have an external fishing neck. It has a box down connection for attaching a Model ‘A’ or ‘N-1’ shank. The Model ‘A’ shank is used to keep the dogs of the Model ‘S’, ‘W’, and ‘Z’ locks in a retracted position while running. The Model N-1 shank is used to keep the dogs retracted in Model ‘G’ and ‘R’ locks while running.
The C-1 Running Tool is dressed with a thread protector for applications that do not require a No-Go on the tool itself. To convert the C-1 Running Tool to a No-Go type running tool, a locating ring is installed in place of the thread protector.
| MODEL ‘C-1' RUNNING TOOL | |||||||
|---|---|---|---|---|---|---|---|
| Tubing Size (in) |
Nipple Seal Bore Size (in) |
Accessory Size (in) |
Running Tool Size (in) |
Locating Ring O.D. (in) |
Top Connection |
F/N O.D. (in) | ‘A’ & ‘N-1’ Shank Size (in) |
| 1.900 | 1.437 | 1.43 | 1.900 - 2-1/16 | 1.468 | 15/16-10 UN | 1.188 | 1.90 |
| 1.500 | 1.50 | 1.520 | |||||
| 2-1/16 | 1.562 | 1.56 | 1.593 | 2-1/16 | |||
| 1.625 | 1.62 | 1.656 | |||||
| 2-3/8 | 1.781 | 1.78 | 2-3/8 | 1.807 | 15/16-10 UN | 1.375 | 2-3/8 |
| 1.812 | 1.81 | 1.843 | |||||
| 1.875 | 1.87 | 1.906 | |||||
| 2-7/8 | 2.062 | 2.06 | 2-7/8 | 2.093 | 15/16-10 UN | 1.750 | 2-7/8 |
| 2.250 | 2.25 | 2.281 | |||||
| 2.312 | 2.31 | 2.343 | |||||
| 3-1/2 | 2.562 | 2.56 | 3-1/2 | 2.593 | |||
| 2.750 | 2.75 | 2.781 2.843 | 1-1/16-10 UN | 2.312 | 3-1/2 | ||
| 2.812 | 2.81 | ||||||
| 4-1/2 | 3.688 | 3.68 | 4-1/2 | 3.718 | 1-1/16-10 UN | 3.125 | 4-1/2 |
| 3.750 | 3.75 | 3.802 | |||||
| 3.812 | 3.81 | 3.835 | |||||
